Posidrive fds 4000 инструкция

Dating > Posidrive fds 4000 инструкция

Download links: → Posidrive fds 4000 инструкция → Posidrive fds 4000 инструкция

For the requirements, see the diagram below. Допускается эксплуатация только с предписанным подключением защитного провода. Таким образом определяются риски, связанные с использованием машины. Перед началом любых работ с преобразователем отключите все источники питающего напряжения!

Result Table Result Table The result of actions e. Description M-Max 1: Maximum torque in % of nominal motor torque. В любом случае, при повышенных частотах вращающегося поля принимайте во внимание указанное снижение номинальных значений параметров. Преобразователи не предназначены для использования в коммунальной низковольтной сети, которая питает жилые районы. Value range in I05: -31 bits to 0 to 31 bits S1-method: Reference of position N10 0: absolute;...

We are giving a lot of attention to the quality of the products and to the packing issue. KG accepts no liability for damages resulting from non-adherence to the instructions or the particular regulations.

POSIDRIVE FDS 4000 - Only all-current sensitive RCD circuit breakers may be used. The drive accelerates to reference speed.

System 19 Technical Specifications 10. Electrical Installation PHYSICAL INSTALLATION Dimension in mm BG I BG II BG III Height Width Frequency inverter, base plate Depth Vertical 282,5 282,5 392,5 Base plate, above mounting holes below Min. Connection Assignment - Control Portion Function Circuiting Term. Inverter Exchange, Compatibility 7. Commissioning Status If no temperature sensor exists, X2. The internal 12 V voltage on X1. This requires a jumper between X1. Default display is 0%. When 100% is reached, remove enable. The release time F06 and application L-level signal. Special functions Parameter record selection Motor potentiometer The FDS inverter supports two separate parameter records. Is the grounding External connection okay? Are there any other wiring errors? A motor with a built-on incremental encoder or SSI encoder is the prerequisite for precise and reproducible positioning. I31 is used to determine the search direction when reference point traversing is started. Positioning Control Example 2: Three fixed positions are always traversed in the Tips: same order pick and place. Positioning Control Example 4: A rotary attachment is to be positioned Solution: The first part of the movement is handled by continuously and without drift in 60° increments. The following tasks are supported. Gearbox tension reduction Torque limit 11. There are several ways to wire the master-slave connection. The angle of deviation is reset when: of master and slave when the power goes off. Description Save parameter: 0: inactive; 1: The parameters of both parameter records are saved in non-volatile memory. Saving is triggered when the value changes from 0 to 1. Description Select parameter set: Two parameter records are available. These can be selected via the binary inputs or directly via A41. The selected parameter record does not become active until the enable has been removed and after a maximum of 300 msec have passed. Description Motor-type: Motor selection from the motor data base. Description Control mode: Specifies the type of motor control. Motor voltage is briefly reduced to prevent overcurrent switchoff. Description M-Max 1: Maximum torque in % of nominal motor torque. Description Operating range n-Min: Parameters C41 to C46 can be used to specify an operating area. All area monitoring procedures are performed at the same time. Is only used for specification of reference value via terminal strip X1 and motor potentiometer. Corresponds to a reverse in direction of rotation. Not related to the selected reference value. Device utilization: Indicates the current load of the inverter in %. Description Option-board: Indication of the option board detected during initialization. See F01, F02 and F06 and F07. Description 10: reference value; Ref. This can be used to generate the standard deviation Continuation from two analog inputs. Description 3: reference value-select 2; See above. Description 26: disable PID-controller; PID controller on AE2 is disabled and the integrator is reset. The drive can be moved Continuation as desired via analog input AE1, for example. The total gain of the control loop is also affected by F22 AE2 gain in addition to G01. The increments of the incremental encoders are specified with F36 and H22. Offset of the static friction i. Value is converted to the motor shaft. Description Parameter record switchover cannot be used for the parameters of groups I, J and L. To save memory space, they are only present once. Position range: 0: limited;... Indication of the unit of measure defined as desired by the user with FDS Tool. Up to 4 characters can be used. For example, this can be used to set the actual position to zero at all Continuation times enable must be active. Effective only when axis is referenced. Manual-traversing and continuous process blocks are stopped at the software stops. Command Process Blocks Para. Description Process block number: Selection of the process block which can be started at all times with posi. Command Process Blocks Para. Switches For description, see chap. Description S1-position: Position of switching point S1. Value range in I05: -31 bits to 0 to 31 bits S1-method: Reference of position N10 0: absolute;... Option Boards ANTRIEBSTECHNIK 14. Press the clip together, and push it into the slit on the housing. Result Table Result Table The result of actions e. Possible results are listed below. Operating States Operating States The operating state is indicated in the display and can be queried under E80 during fieldbus access. If installed when the fault occurs, the Parabox is written automatically. If installed when the fault occurs, the Parabox is written automatically. Block Circuit Diagram Synchronous Running AE2 AE1 extern speed feed forward 14:synchron ref. Block Circuit diagram Reference Value Processing... Parameter Table Parameter Entry Parameter Entry Parameter Entry A.. Inverter Ki-IQ moment D52 Fix ref. Machine Variant-number BE9-function Position range... Parameter Table Parameter Entry Process Block 1 - 8 Block 1 Block 2 Block 3 Block 4 Block 5 Block 6 Block 7 Block 8 J10 to J18 J20 to J28 J30 to J38... Designation Remark Connector for DC link only FDS Chap. Designation Remark 40021 CAN bus, Kommubox CAN bus documentations: Interface module for CAN bus with CANopen profile Publ. Designation Remark 42224 External operator, CONTROLBOX Operating unit for parameterisation and operation of the converters. Connecting lead 2 m is included in the scope of supply. The Drive for Your Automation Presented by: STÖBER ANTRIEBSTECHNIK GmbH + Co.